+86 13812852226    |         sales@aceretech.com
News
Home » News » Industry News » Maintaining and care of plastic crusher

Maintaining and care of plastic crusher

Views: 41     Author: Site Editor     Publish Time: 2022-11-04      Origin: Site

Maintaining and care of plastic crusher

Plastic shredders are used to shred waste plastics and factory plastic scraps. Plastic shredders are widely used in waste plastic recycling and factory scrap recycling. The motor power of the plastic crusher is between 3.5 and 150 kilowatts, and the speed of the cutter roller is generally between 150 and 500 rpm. In terms of structure, there are tangential feeding and top feeding; the knife roll is different from a solid knife roll and a hollow knife roll. Next, let's take a look at the maintenance methods and care precautions for plastic crushers.


Here is the content list:

  • How to maintain plastic crusher.

  • Some precautions for caring for plastic crushers.


How to maintain plastic crusher.


First, the plastic crusher should be placed in a ventilated position to ensure that the motor works to dissipate heat and prolong its life. Second, the bearings should be regularly filled with lubricating oil to ensure lubricity between the bearings. Third, check the screw of the cutter regularly. After the new plastic crusher is used for 1 hour, use the tool to fasten the screw of the moving knife and the fixed knife to strengthen the fixation between the blade and the knife holder. Fourth, to ensure the sharpness of the knife incision, the knife should be checked frequently to ensure its sharpness and reduce unnecessary damage to other parts caused by the dullness of the knife edge. Fifth, when replacing the tool, the gap between the movable knife and the fixed knife: is 0.8MM for crushers above 20HP, and 0.5MM for crushers below 20HP. The thinner the recycled material, the larger the gap can be. Sixth, before the second startup, the remaining debris in the machine room should be removed to reduce the startup resistance. The inertia cover and pulley cover should be opened regularly to clear the ash outlet under the flange because the powder discharged from the plastic crusher chamber enters the shaft bearing. Seventh, the machine should be well-grounded. Eighth, regularly check whether the plastic crusher belt is loose, and adjust it in time.


Some precautions for caring for plastic crushers.


According to the size of the crushed product, the general nozzle and defective products can enter the crushing chamber. If it is a thicker product or a rubber head, it is easier to crush it with a model with one or two levels of horsepower; depending on the size of the crushing chamber, the size of the crushed defective products or the nozzle should not be larger than the size of the crushing chamber; the output requirements of the plastic crusher vary according to different models. After the plastic crusher has been in operation for some time, it should be checked regularly. The hardware is removed, and if the bearing wear is low, it can be turned on a lathe to the correct geometry. At the same time, pay attention to the clearance between the eccentric shaft and the bearing bush and the mandrel and the bearing bush. If it exceeds 1.5 times, it should be replaced or adjusted with a pad. When choosing a plastic crusher, it depends on whether it is reasonable to change the screen and change the knife, whether the crushed material is uniform, whether the powder ratio is within the allowable range, etc. Good plastic crusher manufacturers have undergone strict experiments and verification. The blade is also very important, and the machining of the knife is even a big problem in making a plastic crusher. A good grinder starts smoothly, the safety part is well considered, and the protection is also done well.


Committed to bringing customers more and better products, this is what we have been doing. If you are interested in our plastic crusher products or have other needs, you can contact us, our website is https://www.aceextech.com/, you are welcome, and look forward to cooperating with you. Our company adheres to the corporate culture of "quality first, customer first", and always makes unremitting efforts to become a professional plastic crusher supplier in the industry.


Main Products

Quick Quote

Quick Links

Product Category

Contact Us

Add:18# Yuefeng road, Nanfeng town, Zhangjiagang city. Jiangsu province, China

Tel: +86-512-58622012
Email: sales@aceretech.com
Quick Quote

  Copyrights 2022 Jiangsu Aceretech Machinery Co., Ltd.  All rights reserved.       sitemap | support by Leadong     

ICP备案号:苏ICP备2022010828号-1