+86 13812852226    |         sales@aceretech.com
News
Home » News » Industry News » Precautions for plastic crushers

Precautions for plastic crushers

Views: 41     Author: Site Editor     Publish Time: 2022-10-20      Origin: Site

Precautions for plastic crushers

A plastic crusher, as the name suggests, is a crusher for crushing plastic materials. When the injection molding machine or granulator produces raw materials, the defective products and nozzle materials produced can be put into the plastic crusher in time. After crushing and destruction, keep the crushing and destruction clean and dry, and set the proportion in the "rain material proportional valve". Under this circumstance, the raw materials and nozzles are broken, destroyed, mixed, formed, manufactured into good products, and recycled. Next, let's take a look at the precautions of the plastic crusher.


Here is the content list:

  • Precautions before using a plastic crusher.

  • Precautions after turning on the plastic crusher.


Precautions before using a plastic crusher.


First, before starting, the drive wheel should be moved one or two times by force, and the machine can be turned on after attesting that the movement is flexible and stay until the plastic clincher is running typically before feeding. Second, before stopping the operation, the feeding should be stopped and the material in the machine should be drained, and also the power of the motor should be cut off. Third, pay attention to the temperature of the bearing during operation, keep the bearing in a good lubrication state, and pay attention to whether the sound and vibration are abnormal. When an abnormal situation is set up, stop the vehicle to check whether it's stuck by the anon-breakable object, or whether the machine corridor is damaged. Fourth, keep the feeding of the plastic crusher livery and help to overload. rigorously help unbreakable objects similar to essence and wood from falling into the machine. When it cannot be crushed, the feed humidity shouldn't be too high; when wet crushing, it's necessary to maintain an applicable quantum of water to help to clog due to inadequate flushing and reducing production capacity. Fifth, check whether the flyspeck size of the crushed product meets the requirements. However, the reasons should be set up (similar to the screen gap is too large, the discharge opening being too wide If there are too numerous patches exceeding the specified size.), and applicable measures should be taken to exclude it. Sixth, when the plastic crusher is situated, check whether the fastening bolts are firm and the degree of wear and tear of the fluently worn corridor. For the tooth plastic clincher, you should also use the parking occasion to remove the wood trapped between the teeth. The seventh, worn corridor should be replaced or repaired in time. Eighth, the safety device of the plastic clincher must be kept in good condition, and the safety device mustn't fail to save trouble.


Precautions after turning on the plastic crusher.


First, the plastic clincher and the power unit must be forcefully installed. However, it should be fixed on the cement foundation; if the plastic clincher needs to be flown, the unit should be installed on the frame made of angle iron, If the plastic clincher needs to be fixed for a long time. Second, after the plastic clincher is installed, check the fastening of each fastener, and strain it if it's loose. At the same time, check whether the belt miserliness is applicable. Third, before starting the plastic crusher, first turn the rotor by hand to check whether the claws, hammers, and the rotor are running flexibly and reliably, whether there's any collision in the crushing chamber, and whether the gyration direction of the rotor is harmonious with the direction indicated by the machine arrow, and whether the power machine and the Whether the plastic clincher is well oiled. Fourth, don't replace the pulley casually, in case the speed is too high to beget the crushing chamber to explode, or the speed is too low to affect the working effectiveness of the pulverizer. Fifth, after the plastic clincher is started, it should be kept footing for 2 to 3 twinkles, and there's no abnormal miracle before feeding work. Sixth, pay attention to the operation of the plastic crusher at any time during the work. First, the feeding should be invariant to help the crushing chamber from being blocked; secondly, don't load the work for a long time. However, noise, high temperature of the bearing and the body, if it's set up that there's vibration.


For further plastic crusher-related questions, please communicate with us. Times of accumulated R&D and product experience, to give you further product services and specialized support! Our sanctioned website is https//www.aceextech.com/.


Main Products

Quick Quote

Quick Links

Product Category

Contact Us

Add:18# Yuefeng road, Nanfeng town, Zhangjiagang city. Jiangsu province, China

Tel: +86-512-58622012
Email: sales@aceretech.com
Quick Quote

  Copyrights 2022 Jiangsu Aceretech Machinery Co., Ltd.  All rights reserved.       sitemap | support by Leadong     

ICP备案号:苏ICP备2022010828号-1